Reset Search
 

 

Article

How to Register Material Options, Finishings & Pricing in 2020 Maker

« Go Back

Information

 
Article Number000009398
TitleHow to Register Material Options, Finishings & Pricing in 2020 Maker
Applies to2020 Maker
Body of the Article

    Material Options

    The options creation/editing functionality is located at the bottom of the 2020 Maker home screen, found in the Materials tab where all available vendor materials are located.

    By right clicking on any of these materials, the following options will appear:

    • Add to favorites
    • Hide
    • Create/Edit Model 

    The Create/Edit Model option allows the creation of new models from the chosen material or texture.


    2.gif

     

    Sheet Board Registration  

    When clicking on Create/Edit Model, the following screen will be presented. It is here that the fields for filling in the necessary information for the registration or editing of a new finishing option (model) will be enabled.

     

    mceclip0.png

     

    The information for the sheet board registration is:

    • Model Category
    • Bottom Material
    • Create Model in the Vertical/Horizontal Option
    • Application
    • Material Body
    • Finishing Code
    • Sheet Board Width
    • Sheet Board Length
    • Active
    • Model Data
    • Pricing

    TIP: For agility in the registration process, try to collect all the information above prior to registering as saving the model will only be allowed if all mandatory information is complete.

    Model category

    The model category field refers to the material category to be applied to the model. The categories must be previously registered in the model category register. For this registration, it is mandatory to choose an option.

    This information will also be used in the model selection screen for categorizing them.

    mceclip1.png

    mceclip2.png

     

    The registration of this information is associated with the material used. If any model has already been registered with that material, the model category information will already be filled.

    If the user tries to save a model without any type of application selected, a warning will be displayed.

    mceclip1.png

          

    Bottom Material

    When selecting the upper material to create a finishing model, the system will always fill the bottom material with the same information as the upper. In cases where the upper and bottom materials are the same, no changes are necessary.

    To register a lower material other than the upper one, select the option Change material.

    mceclip2.png

     

    When clicking on the option, the material tab will open, in which the bottom material must be chosen.

    mceclip3.png

     

    If the bottom material does not have a category, it must also be registered.

     

    Create model in the Vertical/Horizontal option

    Due to the presence of grain (vein) in some materials, at times it is necessary to register them vertically and horizontally.          

    mceclip3.png           mceclip4.png

     

    When choosing a registered material as horizontal or vertical, when opening the registration screen, the option create model at vertical option or create model at horizontal option will appear. By checking this option and saving the model, it will be created automatically in the horizontal and vertical options.

    If this field is not checked, the model will be created only in the option where the chosen material was registered.

    mceclip4.png

    mceclip7.png

    If the material does not have this option, it is because it has no grain direction.

    Application

    The field of the application refers to the type of item where the model will be applied. The values of the application field are defined according to the content acquired. These options are not customized by the user and the user will only need to check the options she/he wants in the application model to be registered.

    As soon as any field on the screen is filled in, the tab name will be yellow, indicating that there is information registered.

    mceclip5.png

    If the user tries to save a model without any type of application selected, a warning will be displayed.

    mceclip8.png

     

    Material Body

    The material body field refers to the type of material that the registered model will have. To register an application model, it is necessary to have an option selected and the registration of the material body must already be registered in advance.

    In addition, it is possible to register more than one body of material at a time, noting that each one must have specified information.

    mceclip6.png

     

    When choosing a material body option, the selected option will be added to the side to register the other information related to this material body.

    The finishing, sheet board width and sheet board length information are mandatory.

    Material body - Finish

    For each material body option, it will be necessary to register finishing information. This information must be unique for each registered model and must consist of 5 numeric digits.

    If the value is not correct, a red icon will be displayed alerting the possible registration error.

    mceclip8.png

    If, when saving changes, a saved finishing code already exists, an alert will be displayed informing which model has this code and the operation will not be completed.

     mceclip2.png

    Material Body - Sheet Board Width

    For each material body option, it is necessary to register the sheet board width information. 

    If the value is not filled, a red icon will be displayed alerting the possible registration error.

    mceclip9.png

     

    Material Body - Sheet Board Length

    For each material body option, it is necessary to register the sheet board length information. 

    If the value is not filled, a red icon will be displayed alerting the possible registration error.

    mceclip10.png

     

    Material Body - Active

    For each material body option, it is necessary to register whether this model option will be available to users of the Design version.

    In the Automate and Produce options, the models will always be in the 3D Space regardless of the active/inactive option.

    mceclip11.png

     

    Material Body - Model data

    When all the information is registered, the model information list will automatically be created according to the sheet thickness register. The information contained is:

    • Type - Edge banding type code
    • Thickness - Edge banding thickness name
    • Engineering thickness - Edge banding thickness code/value
    • Height - Edge banding height name
    • Engineering height - Edge banding thickness code/value
    • Reference - Composed by: Type + Engineering thickness + Engineering height + Finish
    • Value - Value in mm

    mceclip12.png

     

    Price Registration

    When registering for a new finishing model, it is possible to register the price of this finishing. The values can be registered in three ways on the model's screen.

    The model prices can also be registered in the specific price tab and their registration is not mandatory but recommended.

    Update Prices Individually

    To update the prices individually, select the line and enter the amount to be registered.

    mceclip0.png

     

    Update All Prices

    If it is necessary to update all prices of the model to be registered, enter the price in the value field and click the Update all prices button.

    mceclip1.png

     

    Update Only Null Prices

    If it is necessary to update all zero prices of the model to be registered, enter the price in the value field and click on the button Update only zero prices.

    mceclip2.png

    URL NameHow-to-Register-Material-Options-Finishings-Pricing-2020-Maker

    Feedback

     

    Was this article helpful?


       

    Feedback

    Please tell us how we can make this article more useful.

    Characters Remaining: 255